SHARP

Language

OAuth 2.0 AUTHENTICATION

When using Microsoft365, Exchange Online, etc. to send e-mails from this machine, it is recommended to use the OAuth 2.0 authentication method.
This section describes how to operate OAuth 2.0 authentication.

GETTING A TOKEN

With OAuth 2.0 authentication, the service provider provides an access token that can be obtained by the machine to send and receive e-mail.
This section describes how to obtain the token.
The settings should be configured by the administrator and executed at the machine. (The configuration cannot be completed on the Web page.)

When an error occurs during job execution, connect test the POP/SMTP authentication connection in the system settings. If [Token update failed. Please delete the token and obtain it again.] is displayed in the connection test result, delete the token and then obtain the token again.

SMTP Authentication Settings

The following settings are available for SMTP authentication, and the setting method is the same for all cases.

  • System Settings → Network Settings → Service Settings (SMTP tab)
  • System Settings → System Control → E-mail Alert and Status → SMTP Settings
  • System Settings → Network Settings → Quick Settings
  • System Settings → Initial Installation Settings → Network Quick Settings
  • This section describes how to obtain a token in System Settings → Network Settings → Service Settings (SMTP tab).

    Tap "Settings (Administrator)" → "System Settings"→ "Network Settings"→ "Service Settings" → "SMTP" tab.

    Configure necessary settings such as "Primary Server", "Port Number", "Timeout", "Sender Name", "Sender Address", and "Enable SSL/TLS" in the SMTP Settings.

    Select "OAuth 2.0" as the Authentication Option.

    Select a provider.

    Enter an account name.

    Tap the [Get Token] key.

    Tap the [Get Token] key, then tap the [OK] key when a confirmation message appears.
    The login page of the selected provider will then be appeared.
    Log in and follow the instructions to obtain the token.
    When a token is acquired, the "Token" display changes from [Not Retrieved] to [Retrieved].

    The following settings are common. When OAuth 2.0 authentication is received for any one of these settings, the settings are updated in concert with each other.

  • System Settings → Network Settings → Service Settings (SMTP tab)
  • System Settings → Network Settings → Quick Settings
  • System Settings → Initial Installation Settings → Network Quick Settings
  • The following settings are independent. Even if you have OAuth 2.0 authentication in other SMTP authentication settings, OAuth 2.0 authentication must be obtained separately.
  • System settings → System Control → E-mail Alert and Status → SMTP Settings
  • POP Authentication Settings

    The following settings are available for POP authentication, and the setting method is the same for all cases.

  • System Settings → Image Send Settings → Internet Fax Settings → Server Settings
  • System Settings → Printer Settings → E-mail Print Settings
  • System Settings → System Control → E-mail Alert and Status → E-mail Status (Advanced Tab)
  • This section describes how to obtain a token in System Settings → Image Send Settings → Internet Fax Settings → Server Settings.

    Tap "Settings (Administrator)" → "System Settings"→ "Image Send Settings"→ "Internet Fax Settings" → "Server Settings".

    Configure necessary settings such as "POP3 Server", "Port Number", "Check Interval", and "Enable SSL/TLS" in the settings.

    Select "OAuth 2.0" as the Authentication Option.

    Perform steps 4 to 6 in SMTP Authentication Settings.

    All POP authentication settings are independent. Even if you have OAuth2.0 authentication in other POP authentication settings, OAuth 2.0 authentication must be obtained separately.

    DELETE A TOKEN

    Delete the tokens that have been set up when using the machine with a new account in Exchange Online , etc. , or when the tokens have expired and can no longer be used. The settings should be configured by the administrator. Token deletion can also be configured from the web page.

    Tap the [Delete] key on each SMTP or POP authentication setting screen to display a confirmation message. Tap the [OK] key to delete the token.
    When the token is deleted, the "Token" display will change to [Not Retrieved].

    CHECKING TOKEN STATUS

    The token status can be checked under "Token" in any setting.

    Display with "Token" Description

    Not Retrieved

    A state in which the token has not been obtained.

    Waiting for authorization

    Permission to obtain a token has been obtained from the provider, but the machine has not completed obtaining the token.

    Retrieved

    The token has been obtained and is activated.

    Invalid

    The token has been obtained, however, the account is not available or the token is invalid because it has expired.

    Language

    Version 03a / bp70m65_usr_03a_us

    ↑Top of page