SHARP

Language

Energy Save

Eco Setting

The machine's power consumption can be reduced by Eco Mode setting. Although each function setting can be changed separately, the machine has the "Custom" and "Eco Mode" to allow simultaneous changing of settings.

Eco Recommendation Function

You can display eco-recommended functions such as two-sided printing and N-Up during copying, document filing print, and direct print.
Setting values applied by each mode is as follows.

Function Custom Mode Eco Mode

Preheat Mode Setting

1min.

1min.

Turn off Panel Display during pre-heat mode

On

On

Auto Power Shut-Off Timer

Remote Job

Earliest

Earliest

Auto Power Shut-Off Timer

Other Job

Fix transition time.:

11min. (for Europe), 1min. (Except for Europe)

Fix transition time.:

1min.

Sleep Mode Power Level

Low Power

Low Power

Eco Scan

On

On (All Modes Except Copy)

Factory default settings:
Disable
Each Energy Save settings in System Settings is not applied when Custom/Eco mode is used.

Display a Message to Delay the Time of Entry into Preheat Mode / Auto Power Shut-Off Mode

Set whether a message is displayed 15 seconds before Preheat Mode or Auto Power Shutoff Mode is entered.

Factory default settings:
Disable

Mode Setting

This function allows you to set the Eco function at once. There are "Custom Mode" and "Eco Mode".

Item Description

Custom Mode

Allows easy machine operation with reduced power consumption.

Eco Mode

Minimizes the machine's power consumption.

Preheat Mode Setting

The time until the preheating mode works is 1 to 60 minutes in 1-minute units (BP-50M26/BP-50M31/BP-50M36/BP-50M45/BP-70M31/BP-70M36/BP-70M45), Set in the range of 1 to 120 minutes (BP-50M55/BP-50M65/BP-70M55/BP-70M65).
Preheat Mode will activate when the set duration of time elapses after printing ends and no further operations are performed. This function reduces your power costs, and at the same time helps conserve natural resources and reduce pollution.
Select the time that best suits the needs of your workplace.
The panel display can be turned Off in the Preheat mode.

Factory default settings:
1 minutes
Preheat mode cannot be disabled.

Turn off Panel Display during pre-heat mode

Set whether the lights on the operation panel turn off in preheat mode.

Factory default settings:
Enable

As soon as the remote job is finished, enter Auto power shut off mode.

This function works in Auto Power Shut-Off mode. When the machine completes a print job received from the PC or outputs received fax data, the machine immediately returns to the Auto Power Shut-Off mode.

Factory default settings:
Enable

Fix transition time.

The Auto Power-Off transition time is fixed. Select [Fix transition time.], and set the transition time in [Auto Power Shut-Off Timer].
When this setting is enabled, the [Change transition time by time of day.] option is disabled.

Factory default settings:
Enable, Auto Power Shut-Off Timer:11 minutes

Change transition time by time of day.

This function controls the transition to Auto Power Shut-Off mode optimally for each time period by analyzing the use of the machine based on job logs obtained during a 4-week period.
When this setting is enabled, the [Fix transition time.] option is disabled.

Factory default settings:
Disable

    • The image transfer control settings are not changed.
    • This does not link to the Power On/Off Scheduling. If both of them are enabled, the Power On/Off Scheduling settings precede.
    • Pages are counted for each paper size separately.
    • When the power supply of the machine was off, there was no job during this time.

Transition to Energy Saving and Auto Power Shut-Off modes

Pattern Transition time Average outputs per hour*

Mode1 (Job Start Priority1)

After 1 hour

700 or more

Mode2 (Job Start Priority2)

After 30 minutes

150 to 699

Mode3 (Energy Saving Priority1)

After 5 minutes

40 to 149

Mode4 (Energy Saving Priority2)

After the minimum time period

0 to 39

Sleep Mode Power Level

Low Power :

The machine switches to the power saving mode, but it takes some time to recover.

Fast Wake Up :

Compared with Low Power, the power value rises by a certain degree, but it results in faster recovery.

Motion Sensor Mode (BP-70C31/BP-70C36/BP-70C45/BP-70C55/BP-70C65)

This enables switching of power saving modes by the motion sensor.

-

* Factory default setting

Auto

This function controls the power optimally for each time period by analyzing the use of machine based on job logs obtained during a certain time period.

If the machine does not have the 4-week job log information, the machine enters the template2 (Mode3 (Energy Saving Priority1) between 8:00 and 18:00 hours). Then after that, it enters Mode4 (Energy Saving Priority2).

Manual

You can set a pattern for each time band.
The machine already has the 3-pattern template. The Energy Save pattern can be added to the "Original Eco Patterns 1 to 4".

Three-pattern template

Template Pattern Description of mode

Template 1

All "Energy Save Priority 2"

The machine runs in the "Mode4 (Energy Saving Priority2)" all the time.

Template 2

8:00-18:00 "Energy Save Priority 1"

The machine runs in "Mode3 (Energy Saving Priority1)" between 8:00 and 18:00, and in "Mode4 (Energy Saving Priority2)" at other times.

Template 3

8:00-18:00 "Job Start Priority 1"

The machine runs in "Mode1 (Job Start Priority1)" between 8:00 and 18:00, and in "Mode4 (Energy Saving Priority2)" at other times.

Sleep Mode Power Level

Low Power :The machine switches to the power saving mode, but it takes some time to recover.
Fast Wake Up :Compared with Low Power, the power value rises by a certain degree, but it results in faster recovery.
Motion Sensor Mode (BP-70C31/BP-70C36/BP-70C45/BP-70C55/BP-70C65) This enables switching of power saving modes by the motion sensor.

Factory default settings:
Low Power

Eco Scan Setting

This setting keeps the fusing unit off when you perform an operation that does not involve printing, such as sending a scanned document.
Set "Eco Scan Setting" to , and select a mode or screen in which to enable Eco Scan Setting.
The following modes and screens can be set.

  • Home Screen
  • Copier
  • Image Send
  • Document Filing
  • System Settings
  • SharpOSA
  • Factory default settings:
    Enable, Home Screen:Disable, Copy:Disable, Image Send:All Enabled, Document Filing:All Enabled, System Settings:Enable, Sharp OSA:All Enabled

    Energy Saving Pattern List

    This function analyzes machine usage and controls entry into auto power shutoff mode based on frequency of use. If you want to manage machine power by using an energy saving pattern list, select [Manual] in [System Settings] - [Eco Setting] - [Change transition time by time of day.], and select an Automatic Update Pattern from the pull-down list or one of Original Eco Patterns 1 to 4.
    To automatically analyze machine usage and update the pattern as needed, set Automatic Update Pattern.

    Edit Pattern

    Set the Original Eco Pattern.

    Item Description

    Change Pattern Name

    To change the pattern name, enter the desired name.

    Pattern to Be Modeled

    Select the stored pattern that you want to base the new pattern on. To copy the settings of a selected pattern, select [Copy the selected pattern.].

    Energy Save

    Set time periods for machine modes. Select a mode from 1 to 4, and select a day of the week, start time, and end time.

    Day of the Week

    Set the day of week on which you want to enable the mode selected in the Energy Save Setting.

    Start Time/Completing Time

    Set the period of time during which you want to enable the mode selected in the Energy Save Setting.

    Specific Date Operation Settings

    You can configure a day on which you have high-output printing or want to perform a special operation as the "specific date" and set a specific energy saving pattern only for that specific date.

    The specific date operation is performed on the day configured as the specific date regardless of the setting on Auto Power-Off transition time (enabled or disabled).

    "Specific Date" tab

    A period of up to 7 days can be set for Specific Date. Set the specific date, energy saving pattern to be applied, and the operation that takes place if the specific date falls on a non-work day.

    Item Description

    Date

    Configure the date on which you want to operate the machine with a specific pattern.

    Select a day between 1 and 31 in Every Month or from End of Every Month.

    Applied Energy Saving Operation

    Select an energy saving patten you want to apply.

    Use the "Pattern" tab to specify the details of the energy saving pattern.

    Operation for Holiday

    Configure how the machine operates if the preset specific date falls on a holiday.

    Use the "Holiday" tab to specify the day as the holiday.

      • If a specific date that is initially specified coincides with the one that is moved because it falls on a holiday, the setting for the former takes precedence.
      • If specific dates of the same dates are configured, they are used in ascending order between 1 and 7 (specific date numbers).

      "Pattern" tab

      This tab is used to configure the details of an energy saving pattern.

      Item Description

      Energy Save Operation

      Select a specific date pattern you want to specify.

      Change Pattern Name

      Enter a pattern name when you want to change the name of a specific date pattern.

      Pattern to Be Modeled

      Select a source pattern when you create a pattern using a stored or preset pattern.

      Add new schedule.

      Add a schedule.

      "Holiday" tab

      Specify a holiday. The day you specified as the holiday will not be a specific date.

      Item Description

      Holiday List

      When you tap this option, the dates and days of the week for the holidays you have set for two years.

      Day of Week

      Use this option to specify a holiday using a day of the week.

      Set Period

      Use this to specify a holiday using a date.

      "Final Registered Time" shows when the holiday that is stored with Set Period was stored.

      Power ON/OFF Schedule Setting

      The machine operator panel can be turned On or Off at a preset time. Up to three (3) patterns can be set. The "Setting 1", "Setting 2" and "Setting 3" are executed in this sequence if set at the same day of week or at the same clock time.

      • The scheduling function does not support the power management settings in the Preheat Mode and Auto Power Shut-Off Mode.
      • The preset power-off time is subject to the following restrictions:
      • If the machine is running due to the current job execution or other reasons, the machine is turned off only after the job has finished.
      • The machine cannot receive printer jobs.
      • The machine can receive output jobs, such as received fax data outputs.
      • If the Time Specified Output of Received Data setting is enabled, they are output next time the machine is turned on.
      • If the power management setting is also enabled, the Power On/Off Scheduling settings precede.
      • If the same time is specified, settings are applied in the order of "Setting 1", "Setting 2", and "Setting 3".
      • The power is not turned off in the following cases:
      • "Automatic deletion when power is turned on" is in progress.
      • The preset power on/off time is within one minute from when the setting is accepted.

      Toner Save Mode

      This mode is used to reduce toner consumption.
      Toner consumption can be set for each print job of "Copy", "Printer", and "Prints (Document Filing)".
      Toner consumption can be selected from three levels.

    • Toner save1 (Toner Consumption: Much)
    • Toner save2 (Toner Consumption: Middle)
    • Toner save3 (Toner Consumption: Little)
    • Factory default settings:
      All Invalid

      Language

      Version 03a / bp70m65_usr_03a_us

      ↑Top of page